News Center

The company has established the enterprise goal of "survival by quality, reputation by quality, and development by quality. Strengthen the training of technical personnel, and constantly enrich the first-line technical force to ensure the normal operation of the quality assurance system.

Homogeneous emulsifying machine fast homogeneous mixing system

Release time:


Homogenizing emulsifying machinesystem composition

1. slow mixing system
The structure of the stirring paddle is of frame type and double stirring type. The middle paddle and the rotating paddle with frame wall are convective stirring, and the working speed of the rotating paddle should be15-60r/min range.
Speed is too slow: the reducer fever serious.
Too fast: the speed reducer is damaged and accelerated. The bracket plate is made of polytetrafluoroethylene, which is adjusted to be flat against the wall of the pot for heat exchange.
1 Two counter-rotating low-speed mixing systems. It consists of a hanger and blade covered with scrapers.
2 The fully automatic movable scraper is made of PTFE material, which can only work when there is material, and is easy to disassemble and clean.
3 concentric axes for dynamic balance.
4 The external hangers and internal blades are made of stainless steel SUS316L.
5 The electronic timer is installed on the PLC to facilitate the adjustment of working time.
6 Equipped with a geared motor-produced by ABB, the speed can be directly adjusted by the inverter, the speed is 0-80 rpm/min.
The slow mixing system creates two separate counter-flows within the material.
(1) A vertical flow along the center forces the material to the bottom of the volume, and its function is to quickly feed the material to the bottom of the homogeneous turbine.
(2) A circumferential annular flow forces the material around the inner wall of the mixing vessel to exchange heat during the heating and cooling stages and to avoid damage to the material due to overheating or overcooling.

2.Homogenizing emulsifying machineFast Homogeneous Mixing System
1 The rapid homogenization mixing action is performed by a turbine installed in the center of the tank bottom.
2 The turbine consists of a toothed stator and a rotor with blades.
3 The turbine is made of SUS316L stainless steel, and the rotating part is passed through a concentric shaft with dynamic balance.
4 The electronic timer is installed on the PLC to adjust the processing time.
5 equipped with deceleration motor -- ABB company production, using frequency conversion speed regulation, speed 0-3000r/min
The characteristics of this structural form ensure a high degree of cleanliness in the processing process for the following reasons:
Because there is no motor flange connection, the material will not produce pollution.
The turbine is set up for easy cleaning, maintenance and handling.
The bottom of the tank is completely smooth and unconnected and easy to clean.
A central valve (option) can be installed to discharge the material.
The mixing and homogenizing motor is installed in the upper part of the tank body, away from the processing area.
Strict protection of the safety of the operator.

3.Homogenizing emulsifying machineHeating/Cooling system
1 heating by the external steam through the jacket to the inner tank heat transfer.
2 The water temperature in the jacket is controlled from the PLC through the temperature controller.
3 The temperature control consists of an electronic temperature control controller and a galvanic couple installed at the bottom of the tank, which can accurately read the actual temperature of the material.
4 Cooling is done directly by external cold water through the jacket.

4. vacuum system
1 water ring vacuum pump.
2 The vacuum gauge indicates the vacuum in the body,
3 The vacuum safety switch is designed to avoid the operation of opening the upper cover under vacuum.
4 The air tightness of the upper cover is guaranteed by the silicon filler on the flange.
5 In theory, the maximum vacuum degree is 730mm/hg at 20 ℃. In order to obtain a perfect emulsification effect, air must be avoided from entering the material. Processing under vacuum allows direct injection of liquid or powder into the volume. 5. upper lid lifting system
The lifting and lowering of the upper cover is completed by a set of hydraulic devices, equipped with a safety limit system, which can keep the upper cover in any desired position.

6. container dumping system
The volume dumping system is used for unloading, which is completed by a manual runner and stays at any angle.

7. processing control
The observation window is equipped with a washer and a lamp for good internal visibility.

8. security system
1. The safety lock prohibits accidental opening of the upper cover under vacuum.
2. The above cover is not properly aligned with the container, and the sealing degree is not enough, so stop using it.
3. If the upper cover is not fully lifted, the dumping function is deactivated.
4. When the upper cover is opened, the mixing and homogenizing motor and vacuum pump are deactivated.
5. The limit micro switch automatically performs opening/closing of the upper cover.
6. The parameters can be changed according to user requirements, and achieve the best performance.