News Center

The company has established the enterprise goal of "survival by quality, reputation by quality, and development by quality. Strengthen the training of technical personnel, and constantly enrich the first-line technical force to ensure the normal operation of the quality assurance system.

What is the use of emulsifying pot steps


Release time:

2019-07-15

Emulsifying pot manufacturer introduction vacuum homogenization emulsifying pot use steps? 1, usually open the vacuum homogenization before the pot first connect the mechanical seal of the cooling water, shutdown and then cut off the cooling water. Tap water can be used for cooling water. Cooling water pressure ≦ 0.2Mpa. Materials must enter the working cavity before starting up, and it is necessary to ensure that they do not run under the condition of material breakage to avoid idling, which may cause the mechanical seal (machine seal) to burn out due to high temperature or affect the service life. Cooling water inlet and outlet joints are equipped with hose size 5mm inner diameter hose. 2. After the emulsifying pot confirms that the machine seal cooling water is connected, start the motor and repeatedly request the motor

  Emulsifying potManufacturer Introductionwhat are the steps of the use of vacuum homogenization emulsifying pot?

1, usually open the vacuum homogenizationEmulsifying potConnect the cooling water of the mechanical seal first, shut down the machine and then cut off the cooling water. Tap water can be used for cooling water. Cooling water pressure ≦ 0.2Mpa. Materials must enter the working cavity before starting up, and it is necessary to ensure that they do not run under the condition of material breakage to avoid idling, which may cause the mechanical seal (machine seal) to burn out due to high temperature or affect the service life. Cooling water inlet and outlet joints are equipped with hose size 5mm inner diameter hose.

  2、Emulsifying potAfter confirming that the cooling water of the machine seal is connected, start the motor, and repeatedly require that the steering of the motor should be consistent with the steering mark of the main shaft before it can operate, and reverse rotation is strictly prohibited!

3. When using a dispersion emulsification homogenizer, the liquid material must be continuously input or kept in a certain amount in the container. Should avoid empty machine operation, so as to avoid the material in the work of high temperature or crystallization solidification and damage to the equipment, no idling!

4, usually only through the high weight to the TRL1 pipeline equipment into the material, the feed must be continuous input, to maintain the material has a good fluidity. However, when the fluidity of the material is poor, when the viscosity is ≧ 4000CP, the inlet of SRH pipeline equipment shall be equipped with a delivery pump with a pumping pressure of 0.3Mpa. The choice of pump should be colloid pump (cam rotor pump), its flow and the selected pipeline typeEmulsifying potto match the flow range. (Should be greater than the minimum flow value and less than the maximum flow value)

5, it is strictly forbidden to metal chips or hard and difficult to break debris into the working cavity, so as not to cause destructive damage to the stator, rotor and equipment.

6, NanoEmulsifying potIn the event of abnormal sound or other faults during operation, stop the machine immediately for inspection, and then run after troubleshooting. The working chamber and stator and rotor shall be cleaned after shutdown.

7. If the process working chamber can be equipped with an additional insulation layer for cooling or heating the material, the coolant or heat transfer oil should be connected first when the machine is turned on. The working pressure of the thermal insulation interlayer is less than or equal to 0.2Mpa. When processing temperature requirements (such as asphalt), it must be heated or cooled to normal working temperature, turned on and turned on.

8. ColloidEmulsifying potWhen used in flammable and explosive working environment, the corresponding level of explosion-proof motor must be selected.

After the production is completed, the equipment must be clean and clean, so as to maintain the working efficiency of the stator and rotor and protect the machine seal. If necessary, a cleaning cycle device is designed and installed near the periphery.

According to the different media used by the user, the import and export filters must be cleaned regularly so as not to reduce the amount of feed and affect the production efficiency. Materials entering the working cavity must be fluid, and materials with dry powder and agglomerates are not allowed to enter the machine directly, otherwise, the machine will be stuffy and the equipment will be damaged.

11. Three-stage pipeline typeEmulsifying potThe stator and rotor shall be inspected regularly. If the wear is too large, the corresponding parts shall be replaced in time to ensure the effect of dispersion and emulsification.

12. If liquid leakage is found at the shaft during operation, the pressure of the machine seal must be adjusted after shutdown. (Attached at the back: detailed description of the mechanical seal)

13. Before using this equipment, corresponding safety production operation procedures should be formulated to ensure the safety of operators and equipment. In the electrical control system, users should set up a safety protection system and have a good and reliable electrical motor grounding device.